Description
- MIX – HOLD – POUR – REVEAL: This silicone mold making kit was developed to create a high-quality, realistic vibrating dong replica that you can make easily in the comfort of your own home.
- MADE WITH BODY-SAFE MATERIALS: The Clone-A-Willy silicone mold kit consists of casting mold powder made from high-grade alginate derived from seaweed with a medical-grade platinum cure silicone – the gold standard of sex toys.
- AN EXACT COPY OF YOUR FAVORITE MEMBER: Our medically tested molds capture incredibly life-like detail, making it the most personalized DIY dick casting kit on the planet!
- MAKE IT VIBRATE: Every clone kit comes with all necessary molding materials to mix and cast, but the fun continues with the included bullet vibrator to that this DIY creation to the next level.
- EASY TO USE: If you can mix, you can cast! This casting kit makes it easy to create a homemade version of your favorite member that’s sure to bring endless pleasure!
And on with us –
Ok. So this requires a lot of preparation. I highly recommend 2 people…. possibly even a 3rd. We read all the reviews and watched lots of fail videos about it but still decided that we could conquer this. The first attempt was a complete and very messy fail. We had the water to the perfect temperature, ( Side note: I feel that some of the other reviewers may have been reading the included thermometer wrong. Make sure you are reading the fahrenheit side. ) the tube was cut and taped so as not to scratch him, we had everything set up so that we could go as fast as possible with timers set for every stage. So first of all from what I understand it is very hard to hold an erection while feeling under pressure from all these time sensitive steps. Finally with a little help from me and his favorite website he got to where he needed to be. I mixed the powder and water and stirred for 1 minute as described. It was very lumpy still when the timer went off but I went ahead and poured the mixture into the tube and proceeded to the next step which presented a logistical problem. The tube is full and he is standing… so I, being very aware of the time just tilted the tube and slapped it over his erection pushing it all the way to his body. In the process of this quite a bit of the molding material rained down onto the floor and all over his legs and feet. He tried really hard to maintain his concentration but the cold wet goo covering him did not help anything. We were still hopeful and waited the 4 minutes plus a little extra as a precaution. Removing the tube was not that fun for him either as he had not done any manscaping in preparation and it did stick a little bit. Once the tube was off we looked at what we had created. It was less than awe inspiring… There were clearly visible bubbles and not a very accurate impression had been made. While he cleaned up both himself and the floor in a 4 foot radius from where he had been standing I mixed the silicone material and poured it into the mold and then slid in and carefully positioned the included vibrator attached to a cardboard square as described. 24 hours later… We pulled the failure from the mold and were super disappointed that not only was it covered in lumps and pits but also the mold had warped a bit and it was shorter and thinner. Also the vibrator had touched the side of the mold and was visibly sticking out a little ways. No way would I ever be using that for anything. So… I am not easily deterred and came back on Amazon and ordered the Alginate powder that another reviewer suggested, a refill kit of the silicone material, some cock rings, and a natural performance enhancer. 3 nights later… I had him lay on the bed on top of towels. I cut both sides of the tube out so that it was open on both sides. He put on the cock ring and got himself to where he needed to be. I measured, poured and mixed everything ( by the way don’t be afraid to use cold water with the alginate powder it will make it set slower ). I came back to him and placed the tube over him and poured the mixture into the tube and over his erection. Then kinda squeezed the tube a bit to make sure it covered everything. We waited 5 minutes and removed it. ( made significantly easier by him having done some manscaping ) and….. Perfect mold!!! No issues with mixing the silicone mixture. I do recommend that after you pour it into the mold you should come back about 1 hour later and pop all the bubbles that have formed at the top. 24 hours later and I now own a perfect replica of my mans “willy”. It is awesome for those times when he isn’t around. Also it was pretty fun even with the fails we were laughing quite a bit during the whole process.
michael –
This is my first time trying. I read the directions and a lot of reviews before attempting. I think my first attempt mold turned out great. Silicone is still setting up so I’ll update after it’s removed. Today is Dec 3rd.
First if you’re doing it alone like I did get everything set up within reach.
Buy a set of rings to wear so you have the right size one and see that it works before attempting, if you go soft it won’t matter how well you followed directions!
I turned the water on kinda slow and made sure it was at right temp coming from faucet and left running.
Put ring on and get good and excited, maybe have a video playing or whatever excites you most.
Have separate timer if you’re using your phone timer.
Put down news paper, this doesn’t come out of cloth material.
I mixed in the 90° water and stirred for around 45 seconds, poured in the mold and quickly inserted.
I touched the side and could see it but couldn’t do anything about it after starting, I’ll let you know about the finish product having this happen. (If you have a partner helping I’d suggest laying down and cutting the bottom of tube off and pouring it in. This would eliminate the need to cut to length as well as position would be easier.
It feels strange but kinda good while it sets. Don’t squeeze the mold while setting.
I did mine standing and some spilt out into towel I had to throw away. It does peel up very easy once set and I wish I didn’t put anything down.
I shaved first decently and whenever there was hair it came off pretty easily and painless considering.
This has a lot of water in the molding material so expect it to shrink some over that four hour dry before silicone mix. Mine did.
I’m about 8″ x1 1/2″ but I have a feeling this is only going to be 5 1/2″ usable with not much room around the vibe. I wasn’t excited as could be which I expected and cut the tube shorter (only you will know if you can get and hold a big hard one while working on something as time restrictive as this instead of the “ah it’s hard enough”) pills might help?
Biggest advice of all, go in light hearted and hope for an experience you enjoyed and learned from while not expecting off the shelf commercial quality perfection. It is your first time ever trying this after all right? Who is perfect doing anything there very first time.
Good luck and enjoy.
In case my update didn’t go through. My first attempt was near perfect. There was a lot of little bubbles in it that made it kinda abrasive. Where I was touching the side it was shiny smooth which now make me think wearing a condom during would yield the best, smoothest finish possible. I may order more and try this. With a ring on your head will be very pronounced and let forgiving than normal which could be a good thing